Jacro 400

TECHNICAL SPECIFICATIONS: 

1. Unit Power Supply :

                - Engine Diesel Kubota 4 Cylinder V3300-E2B-EU-Z4 Made in Original Japan.

                - Power 68 Hp/ 2600 Rpm

                - Hydraulic Power by Piston Pump ADU62+70122RAH Double ETN Vickers

                (For Rotary And For Up/Down )

                - Pressure 3000 Psi/210 bar

                - Hydraulic Tank : 120 litre

                - Diesel Fuel tank : 30 litre

2. Unit Control Device :

                - Hand Control Valve 3Bank 3/4” DTSC Suction IHV-03PC100-A111A8GKJI Integral By

                Italy ( For Hydraulic Rotation, Hydraulic Winch Double, And Hydraulic Wire line Assy ).

                - Hand Control Valve 5Bank ½” DTSC Mono IHV-05-P80-A11111A8GKJI Integral By Italy

                ( For Hydraulic Up Down , Hyd. Sleding Gearbox and Hydraulic Clamp Chuck Assembly ).

                - Relief Valve : For Adjustment pressure up/down Integral RV2-1/2”F Integral By Italy,

                - Max Pressure 3000 Psi. Regulator Valve : For adjustment flow up/down Integral WFC-800

                (1/2”) , Brake Valve : For adjustment brake/ Rem winch /Minute Integral By Italy, CBV2-

                ½” &CBV3- ¾” , Pressure Gauge : By.Skon 0-250 Psi/Bar Umbrella Type

3. Unit Power Device :

3.1 Rotary Head Motor Jacro 400 (RH 5/8”) 6000 Series 112-1089-006 17T By. ETN USA

                - Speed Power : 0-1500 Rpm, Power Pressure : 0-5000 Psi, In/Out Put : ½” SAI 0-Ring

3.2 Up/Down Cylinder Hydraulic Jacro 400 CH Weld Dia Bore ID.85 Rod.50 Stroke 1650mm

                - Torsi Capacity : 915Nm (66641 lb/in), Speed Power : 1000MM/10 Second, In / Out

                Port : 1/2” SAI O-ring

3.3 Wire Line Hydraulic Motor Jacro 400 (RH 2/2) 2000 Series 104-1028-006 By. Eaton ETN USA

                - Torsi Capacity : 452NM (3961 lb/in), Speed Power : 0-250 Rpm, In/Out port : ½” SAI

                O-ring

3.4 Winch Hydraulic Motor Jacro 400 Double RS80-2 Motor (RH 2/2) 4000 Series 109-1215-006 By. ETN USA

                - Torsi Capacity : 915NMC (66641 lb/in). Speed Power : 0-700 Second Rpm, In/Out port : ½” SAI O-Ring

3.5 Cylinder Sleding Gearbox Jacro 400 (RH 2/2) Weld Ø Bore ID.40 Rod.25 Stroke 250mm

                - Torsi Capacity : 272 NM (2219 lb/in), Speed Power : 0-1 Meter/2 Second,

                In/Out port : 3/8” SAI O-ring

3.6 Hydraulic Clamp Chuck Assy Jacro 400 (RH 2/2) Weld Ø Bore ID.40 Rod.25 Stroke 70mm

                - Torsi Capacity : 727 NM (5675 lb/in),

                - Speed Power : 0-1 Meter/1.5 Second

                - In/Out port : ½” SAI O-ring

3.7 Hydraulic Cylinder Lift Mash Jacro 400 ( RH ½” ) Weld Ø Bore ID.63 Rod.40 Stroke 1500mm

                - Torsi Capacity : 117 NM ( 6664 lb/in )

                - Speed Power : 0–500 Second.

                - In / Out Port : 3/8” SAI O-Ring

3.8 Hydraulic Cylinder Jack Mash Jacro 400 Weld Ø Bore ID.63 Rod.40 Stroke 1500 mm

                - Torsi Capacity : 117 NM (6664 lb/in)

                - Speed Power : 0-500 Second

                - In/Out port : 3/8” SAI O-Ring   

                - Oil Cooler : 350 Ltr

                - Water Injection Pump : FMC Pump

                - Drill Pipe : NQ3=400 Mtr, HQ3=300Mtr, &

                PQ=150 Mtr @ 3 meter

                - Drill Bite : Wingbite / PCD

                - Water hose : hose polypipe

                - Core barel : Assy NQ / HQ

OPERATIONAL RECOMMENDATIONS

Capacity Drilling Deep Down:

• NQ 400 Meters (Special Conditions)
• HQ 300 Meters (Special Conditions)
• PQ 100 Meters (Special Conditions)

DRILLING PERFORMANCE

Coal Project:

Open Hole: 70.00 m – 150.00 m /shift

Full Coring: 40.00 m – 100.00 m /shift